Case Study Overview

Site Fire station pump house
Location Saudi Arabia
Repair Type Pipe reinforcement
Defect Six metre section of 150mm steel pipe suffering from heavy corrosion

Repair Products

SylWrap HD Pipe Repair Bandage

Case Study PDF

Case Study Details

The 150mm steel pipe brought water from a reservoir on the lower levels of the pumping house up to the top levels, where it was required for different operations at the fire station.

After many years of service, the pipe was suffering from heavy corrosion. The damage was particularly bad on the section of pipe beneath the surface of the reservoir, where it was exposed to constant contact with water.

Although the pipe had not yet been breached, the metalwork had been weakened to the point where it was only a matter of time before corrosion caused cracks and holes to appear. Replacing the six metre section after this happened would have been difficult because of the shape of the pipe.

There were two 90 degree elbow bends in the pipe. The first changed the pipe direction from running vertically up and out of the reservoir to horizontally at the point where the line reached the upper levels of the building. The second was some 500mm further along, taking the pipe off to the right to connect with valves and equipment.

The complex shape meant that replacing the line would require specially fabricated parts at considerable expense. Not only was the cost prohibitive, but there was the possibility the station might be decommissioned in several years time.

With resources stretched, spending money on the expensive installation of a replacement pipe only for the pump house to be taken out of service within a decade would not have been a good use of funds.

The station therefore sought to carry out pipe reinforcement of the existing steel line instead, strengthening it and protecting it against further corrosion. This would extend the lifespan of the line until a decision was made about the future of the pump house and the station.

It was decided to wrap the entire six metre section in SylWrap HD Pipe Repair Bandage. SylWrap HD is a composite wrap with a water activated resin which sets in minutes to provide an impact resistant protective sleeve around pipes and structures.

Starting from the upper level of the pump house, SylWrap HD was applied to the pipe with a 50 percent overlay. More water was used to smooth the bandage as it was wrapped, moulding it tightly to the line and around both of the bends.

The repair continued in this manner as the line headed down to the lower levels of the pump house, including when the pipe went beneath the surface of the reservoir.

SylWrap can be applied and sets underwater, enabling every part of the pipe to be refurbished. Once fully cured, the bandage formed a rock hard shell encompassing the entire line and offering new strength to the pipe.

Within two hours, the fire station had completed the repair with the entire pipe successfully reinforced. The SylWrap sleeve surrounding the pipe prevented further external corrosion attacking the exterior and weakening the line, reducing the chances of future failure.

In the event of internal corrosion breaching the line from inside, SylWrap would also contain pipe content to prevent any leaks.

Products Used

SylWrap HD Bandage
Composite wrap forms a rock hard, impact resistant protective sleeve around pipework

Related Case Studies

Case Study: Cast Iron Waste Pipe U-Bend Crack Repair Above Hospital Corridor

A cast iron waste pipe with a hairline crack in a U-bend is repaired within the confines of a cramped roof space above a hospital corridor by a maintenance worker on top of a ladder

Case Study: SylWrap Leaking Pipe Repair Passes ASME PCC-2 402-III Qualification Standard

A leak repair using Superfast Aqua PW Epoxy Putty and SylWrap HD passes testing for ASME PCC-2 402-III Qualification – Validation for Repair of Leaking Component

Case Study: UAE Complex Approves SylWrap for Chilled Water District Cooling System Pipe Repair

After rigorous testing, Superfast Aqua PW and SylWrap HD are approved for repairing ABS pipe joints in a chilled water district cooling system at a luxury complex in the UAE

Case Study: Repair of Underground Clay Drainage Pipe Cracked During Building Work

Two cracks in an underground clay drainage pipe – one of which was severe enough to almost split the pipe into two – are sealed by a UK homeowner making a DIY repair

Case Study: SylWrap Composite Pipe Repair Passes ASME PCC-2 401-III Qualification Standard

A composite pipe repair using SylWrap HD and Industrial Metal is independently tested to exceed 309.6 bar, passing ASME PCC-2 401-III – Short Term Spool Survival qualification

Case Study: 150mm Cast Iron Soil Pipe Repair Leaking Wastewater in Hospital Roof Space

A cast iron soil pipe leaking through a two-metre horizontal crack is sealed in a confined roof space, preventing wastewater escaping into the hospital ward below

Case Study: Repair of Corroded Domestic Water Main Pipe Embedded With Stones

Corrosion and stone damage left a domestic water main pipe leaking underneath a driveway until the homeowner repaired and refurbished a 2-metre section of the line